发现很多车主对于变速箱换油保养也是非常不重视，像那种由于缺油导致变速箱内部零件被磨的稀碎的也是非常常见的现象。所以今天就来讲讲
济南变速箱油位的检查方式，如下：
It is found that many car owners also pay little attention to the oil change and maintenance of the transmission. It is also a very common phenomenon that the internal parts of the transmission are worn and broken due to lack of oil. So today we will talk about the inspection method of Jinan transmission oil level, as follows:
变速箱油位检查分两种方法：
There are two methods to check the transmission oil level:
一种是变速箱附带油尺：将车停在水平地面上，拉紧手刹，空挡状态下怠速运转发动机使油温达到60度左右。再进行切换手柄操作，使挡位杆在各挡位停留3秒钟，以便液力变矩器和所有换挡执行器充满液压油，后挂入P挡状态。
One is the oil dipstick attached to the transmission: park the vehicle on the level ground, tighten the hand brake, and idle the engine in neutral to make the oil temperature reach about 60 degrees. Then operate the switch handle to keep the shift lever in each gear for 3 seconds, so that the hydraulic torque converter and all shift actuators are filled with hydraulic oil, and then shift into P gear.
开始检查油尺，先从油管内把油尺拔出来把表面油渍擦干净，再将擦干净的油尺全部插入加油管后再拔出来。观察油面高度，正常油量应该是在上线与下线之间，油尺的2/3刻度处。如果低于低刻度线，说明油少了，如果高于高刻度线，说明油多了。（这里要特别提醒大家，在启动发动机之前一定要确保油尺油浸深度不能小于10mm，然后才能开始进行波箱预热操作。）一种是未带油尺：变速箱没有油尺的话可以通过溢流孔进行检测。溢流孔有的是在变速箱下面，有的是在油底壳上方，有的是在变速箱中壳上面。
Start to check the dipstick. First pull the dipstick out of the oil pipe to clean the oil stains on the surface, and then insert the cleaned dipstick into the oil filling pipe before pulling it out. Observe the oil level height. The normal oil level should be between the upper and lower line, at the 2/3 scale of the dipstick. If it is lower than the low scale mark, it means less oil. If it is higher than the high scale mark, it means more oil. (Here, we should particularly remind you that before starting the engine, you must ensure that the oil immersion depth of the oil dipstick cannot be less than 10mm, and then start the wave box preheating operation.) One is without the oil dipstick: if there is no oil dipstick in the transmission, it can be detected through the overflow hole. The overflow holes are under the transmission, above the oil pan, and above the middle housing of the transmission.
着车状态（注意也有小部分车需要熄火检测）下，拧开油位螺丝，流淌出的油液呈现出“连续的线状”即为正常油位。
When the vehicle is running (note that a small number of vehicles need to be flamed out), unscrew the oil level screw, and the flowing oil shows "continuous linear", which is the normal oil level.
换油的话油品的选择，小编也建议大家好使用原厂油比较稳妥，如果大家有足够的财力想选品质更好的也是可以的，但是切记一定不能比原厂油差，更不能加错油！像干式双离合、湿式双离合变速箱油都是专用的，对变速箱油的要求也是比较高，千万不能图便宜！
When changing the oil, the editor also suggested that it is safer to use the original oil. If you have enough money to choose the better quality oil, you can also do it, but remember that it must not be worse than the original oil, let alone add the wrong oil! For example, the dry double clutch and wet double clutch transmission oil are all special, and the requirements for transmission oil are also relatively high. Don't try to be cheap!
The above is a little knowledge about oil change and maintenance for cars that I compiled for you. I hope it can help you. In addition, if you have any problems with the transmission of the car, you can consult us http://www.jnbsx.com oh
