变速箱维修后是否会有什么影响？维修后有影响，只有两点至关重要的原因，一个是维修人员的技术水平不够稳，工作不够仔细，二就是配件问题。济南自动变速箱维修厂家建议可以把这两点分为四点来说。

Is there any impact after the gearbox is repaired? There are only two important reasons for the impact after maintenance. One is that the technical level of the maintenance personnel is not stable enough and the work is not careful enough. The other is the problem of parts. Jinan automatic transmission maintenance manufacturer suggested that these two points can be divided into four points.

一，维修技师在维修前是否能准确判断故障点。

1、 Whether the maintenance technician can accurately judge the fault point before maintenance.

一个经验丰富的维修技师，通过检查故障代码，试车或是车主的口述，即可快速的说出具体的故障点，这样的话，在维修时候就没有了盲点，拆卸时候只需要更换损坏配件，再认真检查其他没有故障的配件，做好防御工作即可了。而如果没有及时判断出故障点的话，在拆掉时候就会很迷茫，逐一排查，很浪费时间经历，到后即使换了一圈配件，也不见得会修好。

An experienced maintenance technician can quickly tell the specific fault point by checking the fault code, test run or the dictation of the owner. In this way, there is no blind spot during maintenance. During disassembly, only damaged parts need to be replaced, and other parts without fault should be carefully checked to do a good job of defense. If the fault point is not determined in time, it will be very confused when removing it. It is a waste of time and experience to check one by one. Even if a circle of parts is replaced, it is unlikely that they will be repaired.

二，维修技师在维修时候有没有认真判断好损坏的主要原因和间接原因。

2、 Did the maintenance technician carefully judge the main and indirect causes of the damage during maintenance.

某款变速箱本身是十分容易出现头壳漏油的故障的，正常的思维都是更换油封就行了，其实除了油封之外，还有很多造成漏油的间接原因。就比方说是定位环，限位垫片。原车的定位环是橡胶材质的，很容易出现老化变稀的情况，改进的为刚性定位环，可以避免故障。而限位垫片是表面磨光了，改进的限位垫片做了加长，表面还有耐磨层，延长使用寿命。

The gearbox itself is prone to oil leakage from the head case. The normal thinking is to replace the oil seal. In fact, in addition to the oil seal, there are many indirect causes of oil leakage. For example, it is a locating ring and a limiting gasket. The locating ring of the original vehicle is made of rubber, which is prone to aging and thinning. The improved rigid locating ring can avoid failure. The surface of the limit gasket is polished, and the improved limit gasket is lengthened. There is also a wear-resistant layer on the surface, extending the service life.

三，配件是否改进。

3、 Whether the parts have been improved.

有些变速箱是比较容易出现缓冲片故障的。缓冲片材质太薄承受不住变速箱内部常年高温，造成的烧蚀断裂现象，面对于这个情况，很多人会选择更换原厂的缓冲片，其实这个目前是有改进的加宽加厚的缓冲片了，改进的除了加宽加厚这个优点之外，表面还加上了激光打印的耐磨层，更为耐磨一些。缓冲片对比，改进的明显加宽加厚，原车的只有薄薄的一层。

Some transmissions are prone to buffer failure. The material of the buffer plate is too thin to withstand the perennial high temperature inside the gearbox, resulting in ablation and fracture. Faced with this situation, many people will choose to replace the original buffer plate. In fact, there is an improved widened and thickened buffer plate. In addition to the advantage of widening and thickening, the surface of the improved buffer plate is also equipped with a laser printed wear-resistant layer, which is more wear-resistant. Compared with the buffer plate, the improved one is obviously widened and thickened. The original one has only a thin layer.

四，维修技师是否认真安装。

4、 Whether the maintenance technician carefully installs.

在安装配件时候，如果没有认真的安装，拧紧螺丝的话，也是很容易出现后期的故障。所以，在保证配件全部安装的情况下，还要保证好配件的安装程度，有没有松的地方，这一点也是会在维修后，出现故障的。总之，选择做事认真，仔细、为您省钱的维修厂，还是至关重要的一点的。

When installing accessories, if you do not carefully install and tighten the screws, it is also easy to have late failures. Therefore, under the premise of ensuring that all the accessories are installed, it is also necessary to ensure the installation degree of the accessories and whether there is any looseness. This will also cause failures after maintenance. In a word, it is very important to choose a repair shop that is conscientious, careful and saves you money.

变速箱维修后，要想没有什么影响和故障，那就先注意好维修时候，先了解好爱车装配的变速箱，是否有改进配件，找维修技师判断好问题，装配件时候也要让维修技师保证好每个配件的严实性，避免后期故障。更多相关内容就来我们这里http://www.jnbsx.com咨询吧！

After the gearbox is repaired, if there is no impact or fault, pay attention to the maintenance first, understand the gearbox fitted to your car and whether there are any improved parts, find a maintenance technician to judge the problem, and ask the maintenance technician to ensure the tightness of each part when assembling the parts, so as to avoid future faults. Come here for more information http://www.jnbsx.com Consult!