结合我们的日常维修，发现很多车主对于济南变速箱油更换保养也是非常不重视，像那种由于缺油导致变速箱内部零件被磨的稀碎的也是非常常见的现象。那么车子换油保养后出现故障是怎样回事呢?一般有两种情况：

In combination with our daily maintenance, it is found that many car owners also pay little attention to the replacement and maintenance of transmission oil in Jinan. It is also a very common phenomenon that the internal parts of the transmission are worn thin due to lack of oil. So what is the problem with the car after oil change and maintenance? There are generally two situations:

一种是，很多车主车子出现轻微故障的时候，一般都是先换油，以为换油就能解决问题。这种想法本身就是错误的，所以故障可能是换油之前就已经存在了，只是没有得到及时的维修，换油之后越发严重了而已！

One is that many car owners usually change the oil first when there is a slight fault in the car, thinking that changing the oil can solve the problem. This idea itself is wrong, so the fault may have existed before the oil change, but it was not repaired in time, and it became more serious after the oil change!

另外一种就是换完油之后的油位检查，上面我们已经给大家解释了变速箱油多了油少了都会导致变速箱产生故障。所以换油之后的油位检查也是非常重要的一步，这也是很多修理师傅非常容易忽略的一步，所以各位车主在换完油之后一定要记得提醒师傅帮你检查一下油位！

Another way is to check the oil level after changing the oil. We have explained that too much or too little oil in the transmission will cause the transmission to malfunction. Therefore, the oil level inspection after the oil change is also a very important step, which is easily overlooked by many repair workers. Therefore, all vehicle owners must remember to remind the master to check the oil level for you after the oil change!

变速箱油位检查分两种方法：

There are two methods to check the transmission oil level:

一种是变速箱附带油尺：

One is the oil dipstick attached to the transmission:

将车停在水平地面上，拉紧手刹，空挡状态下怠速运转发动机使油温达到60度左右。再进行切换手柄操作，使挡位杆在各挡位停留3秒钟，以便液力变矩器和所有换档执行器充满液压油，后挂入P挡状态。

Park the vehicle on the horizontal ground, tighten the hand brake, and idle the engine in neutral to make the oil temperature reach about 60 degrees. Then operate the switch handle to make the gear lever stay at each gear for 3 seconds, so that the hydraulic torque converter and all shift actuators are filled with hydraulic oil, and then shift to p gear.

开始检查油尺，先从油管内把油尺拔出来把表面油渍擦干净，再将擦干净的油尺全部插入加油管后再拔出来。观察油面高度，正常油量应该是在上线与下线之间，油尺的2/3刻度处。如果低于低刻度线，说明油少了，如果高于高刻度线，说明油多了。（这里要特别提醒大家，在启动发动机之前一定要确保油尺油浸深度不能小于10mm，然后才能开始进行波箱预热操作。）

Start to check the dipstick. First pull out the dipstick from the oil pipe and wipe the oil stain on the surface. Then insert all the cleaned dipstick into the oil filler pipe and then pull it out. Observe the oil level height. The normal oil level should be between the upper line and the lower line, at 2 / 3 of the scale of the dipstick. If it is lower than the low scale mark, it indicates that there is less oil; if it is higher than the high scale mark, it indicates that there is more oil. (I would like to remind you that before starting the engine, make sure that the oil immersion depth of the dipstick is not less than 10mm, and then start the preheating operation of the gearbox.)

一种是未带油尺：

One is without oil dipstick:

变速箱没有油尺的话可以通过溢流孔进行检测。溢流孔有的是在变速箱下面，有的是在油底壳上方，有的是在变速箱中壳上面。着车状态（注意也有小部分车需要熄火检测）下，拧开油位螺丝，流淌出的油液呈现出“连续的线状”即为正常油位。

If the transmission has no dipstick, it can be detected through the overflow hole. Some of the overflow holes are under the gearbox, some are above the oil pan, and some are above the middle case of the gearbox. When the vehicle is in the state of landing (note that a small number of vehicles need to be shut down for detection), unscrew the oil level screw, and the flowing oil shows a "continuous linear shape", which is the normal oil level.

换油的话油品的选择，小编也建议大家好使用原厂油比较稳妥，如果大家有足够的财力想选品质更好的也是可以的，但是切记一定不能比原厂油差，更不能加错油！更多注意事项可来我们网站http://www.jnbsx.com咨询。

When changing the oil, the editor also suggests that it is safe to use the original oil. If you have enough financial resources, you can choose the oil with better quality, but remember that it must not be worse than the original oil, let alone add the wrong oil! For more information, please visit our website http://www.jnbsx.com consulting service